If you hear this beep prematurely, simply stop and go back to the first number of your code. For some reason a button has been pushed unintentionally, either before you started to enter the code, or perhaps, you pushed one number twice by accident. If you hear the beep before the last number, STOP. You will hear a beep when the last number of the sequence is entered and the radio will display a frequency. This is done by pressing the radio preset buttons corresponding with the code numbers. If your radio displays the word CODE, you will need to enter this 5 digit security code. Usually, you will be required to drive the vehicle into the dealership, or at least supply proof of ownership of the vehicle. Some dealers charge for this service, some will do it for free. If you do not have this card, you can have your local dealer supply you with the code.

If you bought your car new, you would have got a credit card sized identification card, with the radio's serial number and code printed on it. This feature is an identification code that is required whenever the radio is disconnected from its power source.Īlmost all BMW radio codes consist of 5 digits between the numbers 1 and 6. The tool plugs into the lighter socket and supplies just enough power to keep the system memories while you perform a short service (battery replacement, etc.).Į23, E24, E28, E30, E32, E34, E36, E36/7, E38, radio, Z3 | Category: BMW 3 Series 84-91 - E30, BMW 3 Series 92-98 - E36, BMW 5 Series 82-88 - E28, BMW 5 Series 89-95 - E34, BMW 6 Series 77-88 - E24, BMW 7 Series 79-87 - E23, BMW 7 Series 88-94 - E32, BMW 8 Series - E31, BMW Z3 96-03 - E36/7īMW has, for many years, used radio's with a theft protection feature. In the future, if you need to inturupt the power to the radio, you can use the Memory Saver Tool. After one hour, turn the radio on (do not change the position of the key) and you should see the CODE function and you can attempt to enter the code again. Now turn the key to the accessory or ignition position (position 1 or 2) and wait for one hour. If, during the entry, or after the code is entered, the radio beeps and says WAIT or CODE WAIT this means that you have entered the code incorrectly (you will get at least two chances to enter the code, before it knocks you out) and you must now perform a reset procedure. In other words (using the same code as above), key 1 is pressed two times, key 2 is pressed three times, key 3 is pressed two times ….

If this doesn’t work you can try Method 2.Ģ) Method 2 – In this case, the code is entered in succession on the memory keys. In other words, if the code were 23241, you would push the 2 key, then 3, then 2, etc. There are two different methods of entering the codes … they are not interchangeable.ġ) Method 1 – If you have 5 or 6 memory keys, the code is entered in the order of the keys. The codes are typically either 4 or 5 digits. When the power is re-connected, the radio will ask for the security code to be input. The anti-theft function is activated when the input power to the radio is interrupted. Then the radio must be left on for 60 minutes before it will accept code entry again.Most BMW models produced up through the mid to late ’90s, employ a radio anti-theft security code. After three tries, it will say CODE WAIT. If the code is mis-entered or wrong, the display will say CODE again. After entering the fifth digit press the > button and the radio will activate. Enter the 5-digit Radio Code using the radios preset buttons.

If the radio display says CODE, it is asking for the code. The radio code can be obtained from these sites: To get out of programming/service mode turn the radio off by pressing the volume control. To scroll through the various displays press the + button on the left upper portion of the radio. The display will change to the radio's serial number. To do this, turn on the radio then, hold down the M button on the left lower portion of the radio's faceplate for about 10 seconds. To retrieve your radio's serial number without removing it from the dash, enter the radio's programming/service mode.

Bmw radio code generator tool alpine